Reset and configure a tp

     

This document describes how to reset và then configure the TP-Link wireless router that may have been supplied with your runclub.vn SME service. You may need to bởi this if you have made changes lớn the router which have resulted in you losing access to the device, or due lớn a forgotten password. These instructions are also valid for a scenario in which the router has accidentally been reset/erased.

Bạn đang xem: Reset and configure a tp

Reset the router

With the routerpowered on, press and hold the RESETbutton on the back of the router for more than 10 seconds until the system LED starts lớn flash quickly. Then release the button & wait for the router to reboot to lớn its factory mặc định settings.

Preparation nguồn up the TP-link router. Connect an ethernet cable between port 1 of the runclub.vn provided NTU & the blue INTERNET port of the TP-Link router. Connect a computer to any of the TP-Link’s yellow ethernet ports using an ethernet cable. Set up your computer

Normally your computer will will be mix up to automatically obtain it"s IP settings. In the case that it isn"t và you have trouble accessing the website management of the router, you can follow the below instructions for Windows computers. The SME runclub.vn team (sme-runclub.vn
runclub.vn.ph) can also direct you lớn instructions for other platforms if required.

On your computer, go to Control Panel > Network & Internet > Network Connections. Click on Ethernet > Properties. Click internet Protocol Version 4 and click Properties at the bottom. On the General tab, make sure that it is set to ‘Obtain an IP address automatically‘ và ‘Obtain DNS server address automatically’.

*

To check that you have already obtained a dynamic IP address, double click on the Ethernet icon và click Details. You should get an IP that starts with 192.168.0.

Xem thêm: Điện Thoại Iphone Xs Max Có Chống Nước Được Không ? Thực Hư Về

*
phối up the router open a website browser & type in 192.168.0.1 Enter the username và password in the login page. The default username and password for TP-Link devices is admin/admin.

*

When you first logged into this device, it will ask you for a new password. runclub.vn will by mặc định set the username & password khổng lồ the same value as for your PPPoE username và password. runclub.vn SME tư vấn can provide these details on request.

*

After you have successfully changed the default username and password, it will redirect you to the Quick thiết đặt and will ask you for the Time Zone. SelectGMT+08:00 to have the same timezone in Philippines and click Next.

*

For mạng internet Connection Type, select PPoE & click Next.

*

Enter your PPPoE username & password (as supplied buy runclub.vn) in the textboxes and click Next.

*

For the Wireless Settings... check the checkbox labeled “Enable Wireless Radio” lớn enable the radio. Network Name (SSID) is what you can see when you want lớn connect to your Wireless network. runclub.vn will have phối this lớn runclub.vn_ The Password textbox contains the password that you need to lớn connect lớn your wireless network. Phối your password here. The mặc định password is listed on a small sticker on the back of the device. Leave the ‘Hide SSID’ checkbox unchecked if you want your Wireless Network to be visible. runclub.vn will have this unchecked. If you have configured all that is needed, click Next.

Xem thêm: Cách Làm Bún Cá Hà Nội Thơm Ngon Chuẩn Vị Không Tanh Ăn Là Ghiền

*
After you click Next, it will show you a summary of the things you configured. If everything looks correct click Save, or if you have something you want lớn change, click Back.

*

After you click Save, the router will redirect you to a page as below. Just click Log In Later.

*

It will then tell you that you have complete the Quick thiết đặt Process. Click Finish.

*

Once finished, it will redirect you khổng lồ a network map. Go to Advanced Tab > Network > Internet, mix MTU kích cỡ to 1492 and click Save.

*

Now disable NAT Boost.Go to Advanced Tab > System Tools. Uncheck the box labeled "NAT Boost" and click Save.
*
This will cause the router reboot so the router will ask you if you want to lớn continue. Click OK.

*

The router will now reboot.

*

Once it has rebooted, lớn Advanced tab > System Tools > Traffic Statistics and turn it on. Click Save. You are now finished with the setup.

*